Feed through lugs are a second set of lugs mounted opposite the mains end on the end of the bussing. They can be used on main lug or main breaker interiors. Sub feed lugs is a replacement set of lugs that is used in place of the main lugs of a panelboard. They allow the installer to subfeed to another panel or device..
Considering this, what does sub feed mean?
An electrical subpanel, also known as a service subpanel or circuit breaker subpanel, acts as a waypoint between the main service panel and branch circuits further down the line. Branch wire circuits lead off of the circuit breakers into various parts of the house.
Additionally, what is a sub feed panel? A subpanel is a smaller service panel that distributes power to a specific area of the home or other buildings on the property. It is essentially a satellite circuit breaker panel that has its own breakers and is usually installed in an area that is convenient to the area it serves.
Also to know, what is a sub feed breaker?
In a sub-feed panel, one of its breakers will be used to provide the connections to the downstream panel. The use of that breaker is the difference in the two types. In both cases, the bus bars of the first panel carry all the current of the first panel, plus all the current of the downstream panel.
What does Main lugs only mean?
Main Lug Only A main lug type load center does not have a main circuit breaker. The incoming supply cables are connected directly to the main lugs and bus bars.
Related Question Answers
How many amps can a sub panel be?
How a Subpanel Works. In modern larger homes, you may sometimes find two main subpanels, each drawing power from the main utility. These are typically homes with 300-amp or 400-amp service, where there is one 200-amp main panel, plus second 100-amp or 200-amp panel.How far can you run a sub panel?
Installing a Subpanel and Choosing Cable You may not know this voltage, so it's best to provide 4 feet. The panel must be easily accessible, so don't install it too far above the floor; 4.5 to 5 feet is about right. The cable you run from the main panel to the subpanel also depends on the amperage rating.Is a sub panel considered a service?
An electrical sub panel can also be known as a service sub panel or circuit breaker sub panel. In essence, an sub electrical panel can be considered a tiny service panel.What is the difference between a main panel and a sub panel?
The biggest difference between a subpanel and a main panel is that the ground and neutral buses on a subpanel have to be separated. Most panels come with a bar joining the two, which is easily removed. Code requires subpanels to have a ground connection that's independent of the main panel's.Does a subpanel need a main disconnect?
Subpanel main breaker A main breaker on a sub-panel is not necessary because this is in the same building (if you are in a different building then NEC 225.31, 225.32, 225.33 apply). That said, having a main breaker in the sub-panel is also acceptable.What is main panel?
A main panel (or service entrance panel) is simply a panelboard that contains the main service disconnect for a property -- this can be up to six circuit breakers in a rule-of-six (split bus) panel, but is more commonly a single main circuit breaker or fused disconnect (such as a pullout).How do you wire a 30 amp sub panel?
Inside the main panel, you'll need two adjacent slots in which you can install a 30-amp, double-pole breaker. Connect the red wire to one of the breakers in the set and the black wire to the other, and then snap the breaker into place. It doesn't matter to which breaker you install either of the wires.How do you size a sub panel?
Subpanel Coverage Area Measure the length and width of each room and multiply them together to find the square footage of the room. Add up the square footage of all of the rooms to find the total square footage. Multiply the total square footage by 3 (watts) to complete the calculation.Can you run a sub panel off a sub panel?
Yes, it's redundant, but it's still required. The wire feeding the new subpanel must be protected from overcurrent by an appropriately-sized breaker. If using both, 1 must be sized for the conductor, and the other can be that size or larger -- convenient if you buy a panel with a 100A breaker preinstalled.How do you run a sub panel in a garage?
Build Your Garage Sub Panel Dig an 18-inch deep trench for the outdoor electrical wire, which you will run from the main panel box to the garage sub panel. Use 1 1/4-inch PVC conduit for a 100-amp sub panel or 1-inch PVC conduit if the sub panel is 50 amps or less. Run the conduit from the garage to the main panel box.What size wire do I need to run a 100 amp subpanel?
A 100 A sub-panel requires a two-pole 100 A breaker - if you want 100 A. You can use #4 AWG 75 deg C or 90 Deg C copper wire in conduit for a 100 A breaker provided the breaker is labeled for use with 75 deg C wire.Can you split a 2 pole breaker?
Re: 2 pole breakers used for 2 single pole circuits So if they are 2 separate circuits but share a neutral, The shared neutral makes them not "two separate" circuits, it makes it "one" multiwire circuit.What size wire do I need for a 60 amp service?
In practice, however, it's common to wire 60-amp breakers with 6-gauge, 3-conductor wire because an appliance that needs a 60-amp breaker seldom draws the full 60 amps. If you're installing a 60-amp subpanel, however, it's best to connect it to the main panel with 4-gauge wire.Do I need to upgrade to 200 amp service?
200 Amps is the minimum recommended service panel size in full size modern homes. Some situations will require significantly more. Larger homes or homes with a machine shop or car lift in the garage can require as many as 400 amps.What is a feed through lug?
Feed-Thru Lugs. A second set of lugs assembled at the opposite end from the mains of the panel. Often used to connect multi-section panelboards or devices to the incoming lines. Available on main lug and main breaker interiors, single phase and three phase.Is a load center a sub panel?
There is no defined difference between a load center and a breaker panel. They are both breaker panels, some with a main and some without. For a sub panel, since there will be a breaker in you main 200 amp panel feeding the subs, it is not required by code to have a main breaker in the subs. Some people just like it!What is a backfeed breaker?
The term “to reverse feed a circuit breaker” means the incoming power supply conductors for a circuit breaker are connected to the terminals on the “OFF” side of the breaker.What does 2 Space 4 circuit mean?
The "2 space, 4 circuit" designation means the panel has only two breaker slots, but you can use twin/skinny/tandem breakers to get 4 circuits. This is WAY to small to do anything reasonable with. Typically these are just used as disconnect boxes for one 240V circuit.Do you bond a sub panel?
The neutral and ground MUST NOT be bonded at a sub-panel. They should only be bonded at the main service panel. If you bond them anywhere other than the main service, the neutral return current now has multiple paths, including though your ground wire. The ground bar should be bonded to the case. 
