Curing of Product RedGard® is dry when it turns solid red, with no visible pink color. Typically, drying time is 1-1.5 hours; depending on ambient conditions, drying time can be as much as 12 hours. After the second coat is applied and both coats are fully cured, the application area can be flood tested..
Keeping this in consideration, how long do you let Thinset dry before applying RedGard?
1 to 1 1/2 hours
Also, how long does waterproofing take to dry? Waterproofing takes at least 24 hours to completely dry, this can be at least a 2-day process for 2-3 coats.
Consequently, can you tile on top of RedGard?
You''ll be fine with thinset over Redguard on walls. It's recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU.
Can you paint over RedGard?
As long as you use a good primer, you should be OK, though. You can apply thinset over the RedGard and prime and paint over that. Joint compound is reactivated when it absorbs water and can cause problems like mold and blistering or delamination of paint film.
Related Question Answers
Do you need to use RedGard over cement board?
As long as it's Cement Board & not some crappy "almost" cement board stuff. You really don't need the RedGard, but the more protection the betterso go for it. And yes, you can do the boards beforehand. But, hit the filled seams & screws (your weak points) as soon as a panel is ready to give it some time to setup.Can I tile over RedGard?
RedGard Creates a Waterproof and Crack Resistant Membrane If you can paint a wall you can use RedGard no problem. And for this shower we only needed one gallon. There are two ways to get RedGard on cement board panels: Roll it on the wall with a 3/4 inch nap roller.Can RedGard be used for shower pan?
Re: RedGard approved as shower pan liner??? Red Guard or similar waterproofing goes over your walls. You can cover your mortar pan with it, but it is not intended to waterproof the pan. You would have to research how to install a mortar pan, but they are best done by skilled tradesman.Do you have to use mesh tape with RedGard?
Use of the reinforcing mesh with RedGard is mandatory at the drain area if you're using it for a shower receptor. I would very strongly recommend it be used at all joints and changes of plane everywhere a traditional pan liner would have been installed, but that's not a manufacturer's requirement.Can I use RedGard on drywall?
It's true that RedGard can be used on drywall, but when all their product information is carefully considered, it is not the case that RedGard can be used on Drywall in a wet area. As far as I can tell, there is no industry standard that supports the use of a liquid membrane on drywall in a wet area.Can you use premixed thinset over redguard?
From what I have read, the premixed thinset does not dry out to form a good adhesive bond when applied over/under a non-permeable membrane like Redguard or the Kerdi-band products. The dry mix (where you add the water on-site) does.How many coats of RedGard can I put on?
To meet the requirements of ANSI A118. 12, apply two coats of RedGard at a rate of 50 sq. ft. per gallon each coat.Can I put RedGard over Kerdi?
RedGuard is not harder to adhere to. There is no reason to use both products although it can be easier to use the RedGuard in corners and niches without the build up you can get with kerdi.What is RedGard used for?
A ready-to-use elastomeric waterproofing membrane for both commercial and residential tile and stone application. Suited for interior and exterior substrates, RedGard® creates a continuous waterproof membrane barrier with outstanding adhesion and reduces crack transmission in tile and stone floors.Will Redgard stick to silicone?
Apply the RedGard SpeedCoat membrane around drain and embed Waterproofing Reinforcing Tape into the membrane, making sure it does not obstruct the drainage weep holes. Membrane will not adhere to silicone when applied on next day. After curing, clamp the upper flange onto the membrane and tighten.Can you use AcrylPro over redguard?
We are using AcrylPro premixed ceramic tile adhesive. Some premixed mortars cannot be used over RedGard, but AcrylPro can.Can you use Redgard on green board?
@Mike Girard MR drywall ("moisture resistant-green board) is absolutely not suitable for active wet locations and topical waterproofing membranes, such as Redguard, will not adhere properly to drywall. Tear it down and start over using cementious backer board.What is the process of waterproofing?
Waterproofing is the process of making an object or structure waterproof or water-resistant so that it remains relatively unaffected by water or resisting the ingress of water under specified conditions. Such items may be used in wet environments or underwater to specified depths.Can you put waterproofing over paint?
Waterproofing Issue You can still apply DRYLOK over latex or oil-based paint but the chemical will not prevent moisture from seeping in through the concrete wall or flooring.How many hours does it take to remodel a bathroom?
On average, a small complete bathroom remodel can be done in about 23 days under ideal circumstances. Assuming no work is done on weekends, this translates to about 4 1/2 weeks—slightly more than one month—if the work proceeds uniformly with no breaks.What is the best waterproofing membrane for showers?
Engineered for both shower walls and bases. Noble also offers a range of extruded polystyrene foam products including preformed shower benches, preformed shower niches, and shower bases. Schluter Kerdi: The Kerdi waterproofing membrane is by far the most popular sheet membrane at the moment.Will Thinset stick to Redgard?
You''ll be fine with thinset over Redguard on walls. It's recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU.Can you use Redgard on basement walls?
There are a number of different waterproofing products that can be used to coat the walls of your basement. RedGard, for example, can be used to seal up leaks and cracks inside and outside of your basement walls. These coatings are like cement, and therefore once they are dry they adhere enduringly. 
