Push the safety valve knob fully in and at the same time place a long match or a butane lighter at the pilot burner. The pilot will light. Hold the safety valve knob in for approximately 60 seconds. If the pilot does not stay lit, turn the safety valve knob to the full OFF position..
Beside this, how do you light the pilot on Real Fyre gas logs?
Match Light: The Match Light lighting method is the most basic method, with no pilot valve assembly at all. Just place your match or lighter in the fireplace near the log burner, turn on the gas with your key valve already installed near your fireplace. Control the flame height by adjusting your key valve.
Subsequently, question is, can a pilot light flame be adjusted? Adjusting the Pilot Flame If the pilot flame is too small, you may be able to make it larger by turning the pilot adjustment screw on the valve control counterclockwise with a screwdriver to open it. The cause of a weak flame may also be an obstruction in the pilot tube.
Accordingly, how do you light the pilot on a gas fireplace?
Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. The pilot should start as soon as the flame is close enough. Hold the pilot button down for about 20 seconds to give the thermocouple time to heat up, then release it. The pilot should stay lit.
How do you light a gas log?
You turn the control knob to the pilot position, push the knob in, light the pilot with a match, then hold the knob down for 30 seconds or so until the pilot stays lit by itself. Once the pilot light will stay lit on its own, you can then move the knob to the "On" position.
Related Question Answers
How do you start a gas fireplace for the first time?
If this is your first time lighting your gas fireplace, you should leave the knob pressed in for 30 seconds to bleed air out of the gas line. After waiting 5-30 seconds for the pilot light to be primed, and with the control knob still pressed in, click in the pilot ignition button located next to the control knob.What is match light ignition?
MATCH-LIT. This is the most basic of the Ignition Systems. The user opens the gas valve manually using the gas valve key and lights the burner with a long match or taper. To turn off you simply close the gas valve.How do you bleed air from gas logs?
While pressing the valve control knob in, press the igniter button repeatedly until the pilot ignites. This could take anywhere from one to 10 minutes to bleed air out of the lines as the gas starts to flow. Once the pilot is lit, continue to press the valve knob inward for 30 seconds before releasing it.How do you clean Real Fyre gas logs?
1 Hold the end of the hose of a shop vac near the Real-Fyre gas logs and turn the vacuum on. 2 Brush the soot and dust from the logs with a soft-bristle brush while vacuuming it away with the shop vac. 3 Turn on the gas burner, and allow the logs to heat for approximately 10 to 15 minutes.How do you light an old gas fireplace?
The pilot knob has three positions: on, off and pilot. Move the pilot knob to the pilot position. This will allow you to push the knob in, which manually releases the flow of gas to the pilot. Now, while holding the pilot knob in, push the igniter button in once every second until the pilot is lit.How do you adjust the pilot light on a gas fireplace?
On some fireplaces, there will be a "Lo-Hi" button that allows you to adjust the flame upward or downward. On others, there will be a screw that you can easily adjust with a screwdriver. Turning the screw clockwise will lower the flame, while a counterclockwise motion will turn it up.Will gas leak if the pilot light goes out?
Carbon monoxide is a colorless, odorless gas produced during burning fuel. It doesn't leak from a pilot light that's gone out, but if the light keeps going out even after you relight the pilot, it can indicate that you have other problems.Should the pilot light always be on in a gas fireplace?
Electronic ignition is when the pilot light on a gas fireplace/insert/stove is only running when the fireplace is on, this means that the unit is likely to have a battery backup as well. A standing pilot is always on, always using a small amount of gas to run constantly unless the gas is physically turned off.Is it dangerous to light a pilot light?
Yes, it is safe to light a pilot light with a gas lighter. If you are trying to relight the pilot light, before turning the knob to the pilot position, wait for some time until the gas smell goes away. If you follow these instructions, it is safe to light a pilot light using gas lighter.Is it dangerous if pilot light goes out on gas fireplace?
A small flow of gas powers the pilot light – just enough to maintain a flame. When a pilot light goes out on a gas fireplace, there is cause for concern if the gas flow hasn't been interrupted. More commonly, a pilot light will go off because of a failure in the supply of gas.Why won't my gas logs light?
Pilot light systems are the most common reason gas fireplaces fail to light, so check the main gas valve to make sure the gas is turned on. If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. Look for and clear out any debris between the igniter and thermocouple.Does a gas fireplace pilot light stay on?
A pilot light means heat, and it also means fuel usage. That flame doesn't stay ignited by magic – it needs gas. When a pilot light burns for long periods of time (like during the summer) without igniting the main burner, a film can develop on the glass doors of the fireplace.How do I check my pilot light?
The pilot gas line is a small metal tube below the burner assembly and distinctive by the slight upturn at the end. It will be apparent, if the pilot is lit, by the small blue flame burning at the end. If you do not see a small blue flame burning, the pilot light is out.How do you adjust a thermocouple?
To adjust the thermocouple, you must tighten the thermocouple nut with a wrench. Take care not to apply too much pressure to the nut -- just tighten it slightly. Then try lighting the pilot. If the pilot won't stay lit, replace the thermocouple with a new one of the same type.What does a thermocouple look like?
The thermocouple looks like a piece of metal tubing smaller than a soda straw. To find it, first locate the gas control box. This is the box that the main gas line enters, where you turn the gas on in the furnace. The other end of the thermocouple sits in the flame of the pilot light.Where is the pilot light adjustment screw?
The pilot adjustment screw is located on the gas valve, just “above” the pilot tube (See Figure 3). Remove the cap screw and find the actual adjustment screw behind it. Turn the screw in to decrease pilot flame, out to increase. 
