How do I program a hunter ICC?

VIDEO

.

Similarly, you may ask, how do you manually turn on a Hunter sprinkler system?

X-Core - Manually Run a Single Station

1. Turn dial to MANUAL – ONE STATION position.
2. Station run time will flash in the display.
3. Turn the dial clockwise to the RUN position to run the station (only the designated station will water, then the controller will return to automatic mode with no change to the previously set program).

Additionally, how do you adjust Hunter sprinklers? Insert the plastic key end of the Hunter wrench into the adjustment socket . While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360° turn of the wrench will increase the arc 90°. Adjust to any arc between 40° and 360°.

In this regard, how do I reset my Hunter ICC?

ICC

1. Turn the dial to the RUN position.
2. Remove the 9V battery.
3. Hold down the , and program buttons simultaneously.
4. While holding down the three buttons, press and release the Reset button on the back of the front panel.
5. Release all three buttons.

How do you test a hunter sprinkler system?

To initiate the test program:

1. Press and hold the PRG button. The station number will be flashing.
2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes.
3. After a 2 second pause, the test program will begin.

Related Question Answers

Why does my sprinkler system keep running?

There are two reasons why your sprinklers would continue running: It's possible your valves have been opened manually. You'll need to locate your valve box(es) and turn the solenoid(s) clockwise until snug. The solenoid is located on the top of the valve and looks like a cylinder with two wires protruding out of it.

How do you open a solenoid valve manually?

Read Article

1. One way is to simply turn the solenoid (the black cylinder with 2 wires) counter-clockwise a 1/4 to 1/2 turn. To shut off the valve, twist the solenoid clockwise until it is snug on the valve.
2. The other way is to use the bleed screw the same way, loosen the screw enough to realease air (1/4 to 1/2 turn).

How long do I run my sprinkler system?

Run your sprinkler and see how long it takes to get a half inch of water in the can – just like a rain gauge. Usually it's about 30 minutes. So 20 minutes, 3 times per week will get an inch of water on your lawn, and 30 minutes 3 times per week will get 1 ½” down.

How do I disable Hunter node?

To turn your controller off, press the button until the icon and Off is displayed on screen. After a short period of time the display will shut off to retain battery power.

Do all sprinkler systems have a master valve?

A master valve is an automatic valve, typically an electric solenoid type valve, that is installed at the point where the irrigation system connects to the water supply. The irrigation controller turns the master valve on and off. Most, but not all, irrigation controllers have a master valve circuit built in to them.

Why does my hunter sprinkler system run twice?

Tabs. A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. The controller will operate the stations in numerical order.

How do I reset my Hunter SRC controller?

SRC Plus Reset

1. Press and hold down the , and buttons.
2. Press and release the RESET button in the lower wiring compartment.
3. Release the , and buttons. The display should now show 12:00a. m.
4. All the memory has been cleared and the controller may now be reprogrammed.

How do I override my hunter thermostat?

Should you want to temporarily override the program—for example, if you stay home from work one day—here's the process:

1. Hold down one of the UP/DOWN arrow keys until the display flashes.
2. Use the arrow keys to move the temperature setting to the desired temperature.
3. Press the HOLD/RETURN button.

How do I reset my sprinkler controller?

How to Reset a Sprinkler System

1. Turn the control dial to the "off" position.
2. Press the "next" button to access the clear-memory feature.
3. Press and hold the "off" button until the display stops blinking.
4. Turn the control dial to the "run" position.
5. Press and hold down the "minus" arrow and "prog" buttons simultaneously.

How do you change a hunter sprinkler solenoid?

1. Turn the controller to "System Off" so it does not try to cycle a program.
2. Shut off the main water supply.
3. Unscrew the solenoid (cylinder with two wires) and make sure the plunger is clean and moves freely.
4. Unscrew the bonnet screws or jar top depending on your valve model.

What does no AC mean on a sprinkler system?

The "NO AC" display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

What is the difference between red and blue Hunter nozzles?

Do you? Both the Red and Blue nozzles will fit the PGP-Adj rotor head. The blue ones have different designations in GPM rather than just a size #. There are also Grey nozzles for lower angle patterns.