How do I blow out my inground pool lines?

Preparation to blow out the lines:

1. Lower the water level 4-12″ below skimmer, depending on cover type.
2. Remove filter, pump and heater drain plugs to drain water, replace loosely.
3. Drain, hand pump or scoop water out of skimmers until almost empty.
4. Set multiport valve to Recirculate, or Filter position for slide valves.

.

Likewise, what size air compressor do I need to blow out pool lines?

The main drain 8 feet down requires a pressure of over 3.46 psi to clear. Plumbing does not hold that much volume. For example, 100 feet of 2 inch PVC is only 2 cubic feet of volume. A compressor that can put out 4 psi and 2 cubic feet per minute will clear the line in 1 minute.

Also Know, do I need to put antifreeze in my pool lines? Not if you blow out your plumbing lines correctly. That is, if there is no water in the pipes to freeze, then there's no need to use antifreeze. However, many folks like to use antifreeze as additional insurance against faulty plugs, or if you're not really certain that all of the water has been blown out.

In this regard, can I blow out my pool lines with a shop vac?

Blow out underground lines. Using the exhaust from a shop vac or similar device, blow water from the skimmer lines at the skimmer so that water comes out at the pump. If the opening in the pool is above water, just blow on and off until no more water comes out.

How far down do you drain your pool for winter?

It's acceptable to drain the pool a few more inches below that if you live in an area that gets heavy precipitation during the winter months. Some pool professionals even suggest draining the water to as much as 6 inches below the skimmer — about the level of the bottom of the pool's return jet.

Related Question Answers

How do you winterize a pool?

Winter Closing

1. Balance the water chemistry.
2. Remove skimmer baskets, wall fittings, cleaners, solar blankets and ladders from the pool.
3. Clean the pool.
4. Lower the water level in the pool.
5. Drain all pool equipment.
6. Lubricate the o-rings on equipment.
7. Winterize plumbing to and from the pool.

Why can't I get suction on my pool vacuum?

Suction-Side Problems Possible reasons for this problem include the following: The water level in the pool is too low. Make sure the water is high enough to cover all the skimmers—if there is more than one—and all the return jets. The suction hose for the vacuum has holes, or it isn't fully connected.

Why my pool skimmer has no suction?

If so try back-washing the filter. If neither of these is the problem, there could be a blockage between the skimmer and the pump. To check open the pump basket and run the garden hose through the line from the pump basket to the skimmer with the water running. Any debris should be flushed back into the pool.

Why does pool skimmer have two holes?

Why Are There Two Holes at the Bottom of a Skimmer Basket? A skimmer is a necessary element of keeping a pool clean. The skimmer sits at the waterline and catches leaves, bugs and trash so they do not clog the filter. Skimmers with a second hole help keep the pump from running dry if the water level is unstable.

Can you snake a pool line?

Run the plumbing snake line into your skimmer's piping until you hit a significant bump. At first you may think it is a turn in the pipe. Try a couple times to push by it. if that doesn't work then you have more than likely found your clog.

Where do you put the antifreeze in your pool lines?

How to Put Antifreeze in Pool Lines

1. Place a sump pump in the pool water. Lower the water level of the pool to just below the jet fixtures and skimmer, using the sump pump.
2. Remove the skimmer lid and basket from the skimmer body. Pour antifreeze directly into the skimmer hole.
3. Place a skimmer plug or gizmo in the skimmer hole.

Is pool antifreeze the same as RV antifreeze?

Pool antifreeze and RV-antifreeze are the same thing. Automotive anti-freeze is something else entirely. It is fine to get some pool/RV antifreeze in the pool, it won't have any lasting effect. It is extremely bad to get automotive antifreeze in the pool.

How much does it cost to winterize a pool?

Most homeowners will spend between $125 and $375 to have their pool winterized by a professional. The national average reported cost is $232.

What is a blow out plug?

Completely clear the water lines with RV blow-out plugs. Attaches and activates the air pump to clear out water lines prior to winterization. Screws the plug to RV city water inlet to blow air in.

What psi do you need to blow out water lines?

Set your air compressor to 30 psi, with a maximum air pressure of 50 psi, and start blowing air into the water inlet. While your compressor is blowing air into your water lines, walk around your RV and open up water valves, one at a time, to blow the water out from the lines.

What size air compressor do I need to blow out water lines?

To properly blow out a sprinkler system, your air compressor needs to provide at least 20 cubic feet per minute. Most irrigation professionals recommend using at least 50 cubic feet per minute.

How do you blow out pool lines with a shop vac?

Blow out underground lines. Using the exhaust from a shop vac or similar device, blow water from the skimmer lines at the skimmer so that water comes out at the pump. Stop and restart the blower repeatedly until no more water comes out at the pump.

How do you drain a hot water line?

1. Shut off the main water valve.
2. Drain pipes of water.
3. Force the water out.
4. Drain appliances.
5. Extra Protection: Pour anti-freeze into all sink and bathtub drains.
6. When you are ready to use the water again, turn on the main water valve and let each fixture run until the pipes are full.